Cisco Network Academy Chapter 4

Cisco Network Academy Chapter 4

음 이거 역시 하반기 챕터 4 인거 같은데

스위치 셋팅하는거 나오는거 같은데 쩝....

다시 한번 책 봐볼까 ㅡㅡ?

Question 1:
Someone got into a router configuration file and changed the password to access privileged mode. Which mode on the router enables you to recover passwords?
A. SETUP
B. RXBOOT
C. Privileged EXEC
D. Global configuration

Question 2:
Which command will indicate the status of IP, IPX, and AppleTalk?
A. show version
B. show interfaces
C. show startup-config
D. show protocols

Question 3:
Which Cisco IOS command shows the amount of NVRAM memory used for the backup configuration file?
A. show mem
B. show flash
C. show running-config
D. show startup-config

Question 4:
In which OSI Layer does the Cisco Discovery Protocol (CDP) operate?
A. Layer 1
B. Layer 2
C. Layer 3
D. Layer 4

Question 5:
What is the correct command to go from the user EXEC mode to the privileged EXEC mode?
A. login
B. enable
C. interface type number
D. configure terminal

Question 6:
Which command shows the status of Ethernet, Serial, BRI, and other ports?
A. show version
B. show interfaces
C. show running-config
D. show startup-config

Question 7:
How many Telnet sessions can a Cisco router have simultaneously?
A. 10
B. 7
C. 5
D. 1

Question 8:
Which Cisco IOS command shows the configuration file stored in NVRAM?
A. show version
B. show running-config
C. show startup-config
D. show interfaces

Question 9:
Which command displays information about the current Cisco IOS software version running on a router?
A. show stacks
B. show version
C. show interface
D. show startup-config

Question 10:
What is stored in working RAM and is constantly updated when the router is working properly?
A. IOS
B. Command Executive
C. Routing Table
D. Active Configuration File

Question 11:
Which Cisco IOS command displays routing table entries?
A. ping
B. trace
C. show ip route
D. show interface

Question 12:
When is the configuration file loaded into RAM?
A. Each time the router is initialized
B. Each time the routing tables are updated
C. Each time the command copy run start is issued
D. Each time the router is place in the priviliged EXEC mode

Question 13:
Which router component provides working memory for configuration files and routing tables?
A. RAM
B. ROM
C. Flash
D. NVRAM

Question 14:
Which router component stores configuration files even when power is off?
A. RAM
B. ROM
C. Flash
D. NVRAM

Question 15:
What is the first thing the router does when power is turned on?
A. Copies the IOS into RAM
B. Executes a bootstrap program
C. Configures the interfaces for IP routing
D. Loads the Startup-Configurations file into RAM

Question 16:
Which response to the appropriate show command indicates an operational serial link?
A. Serial1 is up, line protocol is up
B. Serial1 is up, line protocol is down
C. Serial1 is down, line protocol is down
D. Serial1 is administratively down, line protocol is down

Question 17:
Which port is used to initially configure a router?
A. Auxiliary
B. Console
C. Serial
D. BRI

Question 18:
Which external configuration source is used with a modem?
A. TFTP Server
B. Auxiliary Port
C. Console Terminal
D. Virtual Terminal

Question 19:
The show interface serial Cisco IOS router command can display which one of the following lines of information?
A. DecNET routing is enabled.
B. System image file is c4500-j-mz.
C. Serial1 is up, line protocol is up.
D. IOS (tm) 4500 Software (C4500-J-M), Experimental Version.

Question 20:
Which protocol is used to show summary configuration information about a directly connected Cisco router?
A. Network Control Protocol
B. Cisco Discovery Protocol
C. Address Resolution Protocol
D. Transmission Control Protocol

Question 21:
What is the router prompt for the interface configuration mode?
A. Router(config)#
B. Router(config-if)#
C. Router(config-line)#
D. Router(config-router)#

Question 22:
Which router component is responsible for the power-on bootstrap sequence?
A. RAM
B. ROM
C. Flash
D. NVRAM

Question 23:
Which Cisco IOS command is used to show current telnet connections?
A. show telnet
B. show history
C. show version
D. show sessions.